金属弹簧管性能影响因素的仿真分析

为了研究高温密封组件金属弹簧性能,本文通过对波音公司编网状弹簧管结构和Streck心脏支架结构的研究,建立了编织弹簧的几何拓扑构型和数学模型,推导了弹簧直径计算公式。采用AUTODESK3D-MAX构建了编织弹簧的仿真模型,用ANSYS仿真软件分别从编织丝直径、编织密度以及编织方法 3方面探究不同测试对弹簧性能的影响。结果表明,增加弹簧丝直径、降低弹簧管轴向方向的编织密度、提高圆周方向的编织密度、向外的弹簧管编织方式可有效提高弹簧管的回弹性能。     

超弹性N形杆纯弯曲力矩理论建模和试验验证

为了使N形杆在空间结构中顺利展开,对其缠绕过程中的力学特性进行了分析。基于协变基向量法建立了纯弯曲条件下各向同性单片带簧在缠绕时应变能理论模型,并采用最小势能原理推导了弯矩的理论模型,然后通过拟合曲率推导了N形杆缠绕时的理论模型。研制了4根N形杆样件,并搭建了试验平台,使用数显式推拉力计分别对杆件在缠绕过程的拉力进行了5次测试,然后求出峰值力矩,发现试验值与理论值的偏差不大于8.83%,偏差平均值为2.813%,从而验证了理论模型的准确性。该研究可用来分析超弹性杆在纯弯曲状态下的峰值力矩,对超弹性杆在宇航空间中的应用具有重大意义。     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

舱段结构热振耦合环境下仿真分析

针对武器装备对环境适应性要求不断提高的现状,以某舱段结构为研究对象,基于高加速应力筛选试验(HASS)条件,研究了结构在温变-振动耦合环境下的失效机理。首先,结合HASS试验剖面,确定了载荷条件,建立有限元模型;其次,采用ANSYS Workbench软件分析得到结构温度场分布及应力响应,确定了结构危险位置,并对其疲劳寿命进行计算分析,为舱段结构的失效分析及HASS试验剖面的合理制定提供依据和指导。     

基于Solid-Works的齿轮参数化设计

由于Solid-Works2003及以前版本的软件，其标准件图库中没有绘制各种齿轮的功能，本文介绍了在Solid-Works中实现参数化齿轮三维造型的一种方法，应用此方法可以在Solid-Works环境下完成齿轮的参数化三维绘制。     

套齿连接转子简化建模及动力特性分析

在进行转子和整机计算时建立套齿结构接触模型会增加计算量，降低计算效率，直接将套齿结构省略又无法体现其刚 度特性变化对转子动力特性的影响。针对该问题，基于航空发动机单圆柱面套齿连接的结构和力学特征，建立了考虑构件间界面 接触状态的力学特征分析模型，提出了考虑套齿结构刚度随参数变化的简化建模方法，并与套齿接触模型进行了对比分析。建立 了单圆柱面套齿连接结构转子简化模型，开展了相应的转子动力特性试验，对比分析了拧紧力矩对转子模态频率的影响。结果表 明：转子简化模型与试验模型最大计算误差小于5%，证明套齿结构简化建模方法具有较高的可靠性和准确性，可为工程实践中高 效开展含套齿结构转子及整机动力学准确计算分析提供方法与参考。     

水平表面气流剪切作用下的水膜厚度

飞机结冰表面上的液态水受气流吹拂作用会发生向后溢流,从而影响结冰区域范围及防冰系统设计;为了获得水膜流动规律,对水平平板表面上气流剪切驱动的水膜流动进行了实验测量和建模分析。通过水膜流动风洞试验台产生高速气流驱动水膜的流动,使用色散共焦位移计测量同一位置的水膜在不同时刻的厚度变化,结果表明气-液界面由底层薄水膜和多种尺度的波动组成,具有变化速度快随机性强的特点。通过水膜厚度随气流速度及水膜雷诺数的变化规律,发现平均水膜厚度与两者均呈现出单调非线性的依赖关系。基于薄水膜流动理论和平均水膜厚度实验结果,提出了高速气流剪切作用下的气-液波动界面剪切因子计算式,适用于风速17.8~52.2m/s,水膜雷诺数26~128之间的平板水膜流动计算。     

基于正弦基础激励的航天器结构模型修正方法

正弦振动试验是航天器系统级和单机产品需要开展的常规试验,充分利用工程中积累的正弦试验数据进行结构模型修正具有重要的工程意义。文章首先介绍了基础激励下结构模型修正方法,通过矩阵分块、待修正参数归一化、参与修正的频率点选择等步骤,推导出基于基础激励的模型修正公式;然后对国际通用算例GARTEUR桁架结构的有限元模型进行修正,分析修正后模型在修正频段内和修正频段外计算所得模态频率,验证修正后模型对模态频率的复现和预示能力,通过对比试验模型、分析模型和修正后模型中4个典型节点的响应曲线,检验修正后模型精度。结果表明:修正后模型的模态频率和响应曲线均与试验模型趋于一致,证实了该修正方法对GARTEUR结构修正的有效性。     

Solar activity variations of ionosonde measurements and modeling results

The time series of hourly electron density profiles N(h) obtained at several mid-latitude stations in Europe have been used to obtain N(h) profiles on a monthly basis and to extract both the expected bottomside parameters and a proxy of the ionospheric variability as functions of time and height. With these data we present advances on a “Local Model” technique for the parameters B0 and B1, its applicability to other ionospheric stations, to other bottomside ionospheric parameters, and to modeling the time/height variability of the profile. The Local Model (LM) is an empirical model based on the experimental results of the solar activity dependence of the daily and seasonal behavior of the above parameters. The LM improves the IRI-2001 prediction of the B0 and B1 by factor of two at mid-latitudes. Moreover, the LM can be used to simulate other ionospheric parameters and to build mean N(h) profiles and the deviations from them. The modeling of both the average N(h) profiles and their deviations is an useful tool for ionospheric model users who want to know both the expected patterns and their deviations.